stream_temp();
//stream_magno();
}
-/* Copyright (c) 2015, Ian Sutton <ian@kremlin.cc>
-
- * Permission to use, copy, modify, and/or distribute this software for any
- * purpose with or without fee is hereby granted, provided that the above
- * copyright notice and this permission notice appear in all copies.
- *
- * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
- * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
- * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
- * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
- * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
- * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. */
-
- /* this is a library for the arduino due that controls the LSM303D accelerometer
- * & magnometer. it will not work on other arduino models, it uses API calls
- * exclusive to newer ARM-based arduinos.
- *
- * steps to recreate:
- *
- * !! be especially careful of the 5V output in on the due's SPI header. it is a high !!
- * !! current output & will cook anything nearby. refer to this diagram before making !!
- * !! any connections: http://uglyman.kremlin.cc/quick/due-pinout-web.png !!
- *
- * - wire SPI ports on the LSM to their respective pins on the due's SPI header (not
- * ICSP!)
- *
- * - wire INT2 to digital pin 53 and the LSM's chip select/slave select port to
- * pin 10 above the pwm module.
- *
- * - ground the SPI module, arduino, and LSM together, preferably alone. i had to use
- * an audio isolation amplifier to provide a quiet enough ground to support the
- * unusually high SPI baud rate i use here, discussed later.
- *
- * - wire LSM's Vin to the arduino's 3.3V supply. leave Vdd floating */
-
-#include <SPI.h>
-
-/* slave select pin */
-#define LSM_CS 10
-
-/* wire to INT2 which latches to a magnometer-read-ready signal */
-#define MAGNO_RDY_PIN 53
-
-/* SPI clock divider (84MHz divided by this equals SPI frequency) */
-#define SPI_CLK_DIV 3
-
-/* frequency of temperature sensor in Hz, set in lsm_config() */
-#define TEMP_FREQ 100
-
-/* struct representing magnometer values at shared instant of time */
-struct magno_point {
-
- signed short x;
- signed short y;
- signed short z;
-};
-
-/* hands off */
-const byte BAD_REGS[8] = { 0x00, 0x01, 0x02, 0x03, 0x04, 0x0E, 0x10, 0x11 };
-
-/* these are set on successful completion of their respective funcs */
-bool SERIAL_CONFIGURED = 0;
-bool SPI_CONFIGURED = 0;
-bool SPI_OK = 0;
-bool LSM_CONFIGURED = 0;
-
-/* don't brick the LSM */
-bool matches_badreg(byte addr) {
-
- short i;
- i = 0;
-
- for (; i < 8; i++)
- if (addr == BAD_REGS[i])
- return true;
-
- return false;
-}
-
-/* fired when critical exception encountered, doesn't return */
-void killspin(String msg) {
-
- Serial.println(msg);
- Serial.println("exception occurred or assertion failed. no-operation until reset");
- while (1);
-}
-
-/* reads n sequential bytes starting @ addr returns byte array of size n
- * returned array must be free()'d manually! */
-byte *spi_multiread(byte addr, short n) {
-
- byte *ret, first;
- short cnt;
-
- if (matches_badreg(addr))
- killspin("tried to read from a reserved, internal register!");
-
- if (!SPI_CONFIGURED || !SPI_OK)
- killspin("tried to read over SPI before it was configured or tested!");
-
- /* addresses are 6 bits wide */
- if (addr > 63)
- killspin("invalid lsm register address");
-
- /* set msb to read, 2nd msb for multibyte op, and append 6 bit address field */
- first = 128 + 64 + addr;
- cnt = 0;
-
- /* free this! */
- ret = (byte *) calloc(n, 1);
-
- /* kickoff read operation */
- SPI.transfer(LSM_CS, first, SPI_CONTINUE);
-
- for (; cnt < n - 1; cnt++)
- ret[cnt] = SPI.transfer(LSM_CS, first, SPI_CONTINUE);
-
- ret[n - 1] = SPI.transfer(LSM_CS, first, SPI_LAST);
-
- return ret;
-}
-
-/* reads & returns 1 byte @ addr */
-byte spi_read(byte addr) {
-
- byte first, ret;
-
- if (matches_badreg(addr))
- killspin("tried to read from a reserved, internal register!");
-
- if (!SPI_CONFIGURED || !SPI_OK)
- killspin("tried to read over SPI before it was configured or tested!");
-
- /* addresses are 6 bits wide */
- if (addr > 63)
- killspin("invalid lsm register address");
-
- /* set msb to read and append 6 bit address field */
- first = 128 + addr;
-
- /* perform 16 bit SPI exchange as per LSM datasheet's specification */
- SPI.transfer(LSM_CS, first, SPI_CONTINUE);
- ret = SPI.transfer(LSM_CS, 0x00, SPI_LAST);
-
- return ret;
-}
-
-/* write single byte @ addr */
-void spi_write(byte addr, byte data) {
-
- byte first;
-
- if (matches_badreg(addr))
- killspin("tried to write to a reserved, internal register!");
-
- if (!SPI_CONFIGURED || !SPI_OK)
- killspin("tried to write over SPI before it was configured or tested!");
-
- /* addresses are 6 bits wide */
- if (addr > 63)
- killspin("INVALID ADDRESS");
-
- /* set 6 bit address field */
- first = addr;
-
- /* perform 16 bit SPI exchange as per LSM datasheet's specification */
- SPI.transfer(LSM_CS, first, SPI_CONTINUE);
- SPI.transfer(LSM_CS, data, SPI_LAST);
-}
-
-void spi_config() {
-
- SPI.begin(LSM_CS);
-
- /* my arduino due has a 84 MHz cpu which is divided here to provide the
- * SPI baud rate. the LSM's data sheet purports the maximum SPI frequency
- * is 10MHz, however i've found that it works fine up to 28MHz, which is
- * the frequency set below (84 MHz / 3 = 28 MHz) */
- SPI.setClockDivider(LSM_CS, SPI_CLK_DIV);
-
- /* LSM is big endian */
- SPI.setBitOrder(LSM_CS, MSBFIRST);
-
- /* clock is active-low, exchange occurs on clock's first falling edge
- * CPOL = 1, CKE = 0 */
- SPI.setDataMode(LSM_CS, SPI_MODE3);
-
- SPI_CONFIGURED = 1;
-}
-
-/* read & check immutable device ID reg a number of times to guarantee LSM
- * slave is responding and capable of handling master's SPI clock freq.
- * then, write reg & read back to test writing */
-boolean spi_test() {
-
- bool read_ok, write_ok;
- byte i;
-
- i = 0;
- read_ok = true;
- write_ok = true;
-
- if (!SPI_CONFIGURED)
- killspin("tried to test SPI before it was configured!");
-
- /* cheat a little here */
- SPI_OK = 1;
-
- /* test reading */
- Serial.print(" [READ: ");
-
- for (; i < 100; i++)
- if (spi_read(0x0F) != 0x49)
- read_ok = false;
-
- if (read_ok)
- Serial.print("OK, WRITE: ");
- else
- Serial.print("FAIL, WRITE: ");
-
- /* test writing with */
- i = 0;
- for (; i < 100; i++) {
-
- spi_write(0x17, i);
-
- /* uncomment for write debugging
- Serial.print("WROTE ");
- Serial.print(i);
- Serial.print(" GOT ");
- Serial.println(spi_read(0x17));*/
-
- if (spi_read(0x17) != i)
- write_ok = false;
- }
-
- /* write back datasheet-defined default value to test
- * register we used (OFFSET_X_L_M) */
- if (write_ok)
- spi_write(0x17, 0x00);
-
- /* finish up */
- if (write_ok)
- Serial.print("OK] ");
- else
- Serial.print("FAIL] ");
-
- if (read_ok && write_ok) {
-
- SPI_OK = 1;
- return true;
-
- } else {
-
- SPI_OK = 0;
- Serial.println(":: failed!");
- return false;
- }
-}
-
-void lsm_config() {
-
- if (!SPI_CONFIGURED || !SPI_OK)
- killspin("tried to configure lsm before spi was configured & tested");
-
- /* set 16 bit 2's comp. magnetic field offset values for x, y, z.
- * these default to zero as correct offset values depend on your geographical
- * location. you can find the current magnetic field strength at your coords
- * using NOAA's database: http://www.ngdc.noaa.gov/geomag-web/#igrfwmm
- *
- * in the WMM model, the significant values are north comp (z offset), east comp
- * (x offset), and vertical comp (y offset). you can ignore the 'change/year' and
- * 'uncertainty' values
- *
- * you must translate the given tesla values into corresponding gauss equivalents
- * and scale them according to the range specified later in this function. you will
- * usually use the +2:-2 gauss scale. here is an example conversion for
- * latitude 43° 2' 14" N, longitude 76° 7' 36" W (near syracuse university in
- * syracuse, NY 13210), 0 meters above sea level, taken on february 16th, 2015 at 07:32 UTC:
- *
- * [x] :: -4,129.9 nanoteslas :: -0.041299 gauss
- * [y] :: 49,817.8 nanoteslas :: 0.498178 gauss
- * [z] :: 18,755.9 nanoteslas :: 0.187559 gauss
- *
- * next, we need to fit these values into our 4-gauss scale (spanning from +2 gauss
- * to -2 gauss) in the context of a 16-bit signed number. to do this, take the gauss value
- * and divide it by 2. take this number, and multiply it by 2^15 - 1. round to closest integer.
- * finally, multiply this value by -1 as the offset value combined with the sensed value should
- * result in zero. negatives should be expressed as two's complement. here are the offsets derived
- * from the previous values:
- *
- * [x] :: 677 :: 0x02A5
- * [y] :: -16,324 :: 0xC03C
- * [z] :: -6,146 :: 0xE7FE
- */
- const byte x_lo_offset = 0xA5;
- const byte x_hi_offset = 0x02;
-
- const byte y_lo_offset = 0x3C;
- const byte y_hi_offset = 0xC0;
-
- const byte z_lo_offset = 0xFE;
- const byte z_hi_offset = 0xE7;
-
- spi_write(0x16, x_lo_offset);
- spi_write(0x17, x_hi_offset);
-
- spi_write(0x18, y_lo_offset);
- spi_write(0x19, y_hi_offset);
-
- spi_write(0x1A, z_lo_offset);
- spi_write(0x1B, z_hi_offset);
-
- /* latch magnometer-ready to INT2 output pin */
- spi_write(0x23, 0x04);
-
- /* enable temperature sensor,
- * select high magnetic resolution,
- * select 100Hz sensor rate */
- spi_write(0x24, 0xF4);
-
- /* set full scale of magnetometer to +2:-2 gauss as
- * earth's field is usually between +0.65:-0.65 G */
- spi_write(0x25, 0x00);
-
- /* switch on magnometer, to continuous conversion mode */
- spi_write(0x26, 0x00);
-
- LSM_CONFIGURED = 1;
-}
-
-/* returns a size-n array of readings from temperature sensor. function waits
- * between reads for a time equal to the period length of the sensor as to avoid
- * multiple reads of an un-updated value. this is a hack to get around the fact
- * this chip does not have a TEMP_READY bit in a status register like the magnometer
- * or accelerometer do.
- * caller must free() returned pointer */
-signed short *pull_temp_values(int n) {
-
- signed short *ret;
- int sensor_period, i;
- byte *temp_pair, *sync_pair_i, *sync_pair_f;
-
- /* period length in milliseconds of temperature sensor refresh */
- sensor_period = 1000 / TEMP_FREQ;
-
- i = 0;
- ret = (signed short *) calloc(n, 2);
-
- sync_pair_i = sync_pair_f = spi_multiread(0x05, 2);
-
- /* spin until sensor cranks */
- while (sync_pair_i == sync_pair_f)
- sync_pair_f = spi_multiread(0x05, 2);
-
- /* wait until mid-period to read as to avoid edge-case duplicates */
- delay(sensor_period / 2);
-
- for (; i < n; i++) {
- temp_pair = spi_multiread(0x05, 2);
- ret[i] = word(temp_pair[1], temp_pair[0]);
- free(temp_pair);
- delay(sensor_period);
- }
-
- free(sync_pair_i);
- free(sync_pair_f);
-
- return ret;
-}
-
-/* returns a magno_point struct from passed 48 bit input taken from magno sensors */
-struct magno_point parse_raw_magno_data(byte *in) {
-
- struct magno_point ret;
-
- ret.x = word(in[1], in[0]);
- ret.y = word(in[3], in[2]);
- ret.z = word(in[5], in[4]);
-
- return ret;
-}
-
-/* returns a size-n array of readings from magnometer. result contains 3 words
- * describing felt magnetic field strengths x, y, z directions. function polls INT2
- * (latched to magnometer-ready signal) until it goes high before reading from sensor.
- * this guarantees each member in returned array is a genuine, non-repeat value from a
- * single magnometer sensor cycle
- * caller must free() returned pointer */
-struct magno_point *pull_magno_values(int n) {
-
- struct magno_point *ret;
- int i;
-
- i = 0;
- ret = (struct magno_point *) calloc(n, sizeof(struct magno_point));
-
- for(; i < n; i++) {
-
- /* spin until sensors are fresh */
- while(digitalRead(MAGNO_RDY_PIN) != 1);
-
- ret[i] = parse_raw_magno_data(spi_multiread(0x08, 6));
- }
-
- return ret;
-}
-
-void setup() {
-
- /* set up magno. read ready signal */
- pinMode(MAGNO_RDY_PIN, INPUT);
-
- /* this is about as fast as you can get on the serial console */
- Serial.begin(115200);
- SERIAL_CONFIGURED = 1;
-
- /* spi init */
- Serial.print("configuring spi..");
- spi_config();
- Serial.println("done");
-
- /* spi check */
- Serial.print("testing spi..");
- if (spi_test())
- Serial.println("done");
- else
- killspin("SPI test failed. perhaps the device is not wired correctly or your frequency is too high");
-
- /* lsm init */
- Serial.print("configuring lsm..");
- lsm_config();
- Serial.println("done");
-}
-
-/* demonstration of realtime temperature stream. does not return */
-void stream_temp() {
-
- for(;;) {
- signed short *temp_vals;
- temp_vals = pull_temp_values(100);
-
- for (int i = 0; i < 100; i++) {
- if(!(i % 20) && i)
- Serial.print('\n');
- else if(i)
- Serial.print(" ");
-
- Serial.print(temp_vals[i], DEC);
- }
-
- Serial.println("\n--------------------------------------------------------------------------------");
-
- free(temp_vals);
- }
-}
-
-/* demonstration of realtime magnometer stream. does not return */
-void stream_magno() {
-
- struct magno_point *read_buf;
-
- read_buf = pull_magno_values(100);
-
- for(int i = 0; i < 100; i++) {
-
- Serial.print("X: ");
- Serial.println(read_buf[i].x, DEC);
- Serial.print("Y: ");
- Serial.println(read_buf[i].y, DEC);
- Serial.print("Z: ");
- Serial.println(read_buf[i].z, DEC);
- Serial.println("---------");
- }
-
- free(read_buf);
-}
-
-void loop() {
-
- stream_temp();
- //stream_magno();
-}
projects / grab_bag.git / commitdiff